SINUMERIK 西门子840D系统换刀参数总结及常用参数 - 有事我帮您专业数控工控博客技术论文

    SINUMERIK 840D系统：古德机电黄工13146520731 销售西门子数控系统提供维修
    22550 TOOL_CHANGE_MODE ：T功能执行后，是否立即装载新刀。
    0：立即执行。
    准备刀和换刀在一个NCK程序块里。例如，执行T后，激活新的刀具偏差（参阅20270: CUTTING_EDGE_DEFAULT）
    1：执行T功能后，准备装载新刀。这个功能主要用于带刀库的铣床，主要是为了换刀是不影响加工。
    22560 TOOL_CHANGE_M_CODE
    从主轴上移去旧刀并装载新刀。换刀需要执行M06，同DIN66025一致。
    20121:
    The next tool is preselected with MD 20121: TOOL_PRESEL_RESET_VALUE whose assigned tool length compensation values must be taken into account on RESET and power up according to MD 20110: RESET_MODE_MASK are to be taken into account.
    20270: 未编程前刀具切削沿的初始位置
    = 1 M06之后没有自动选择刀沿号
    0 M06之后自动选择刀沿号=
    = –1 M06之后保留旧刀刀沿号并为新刀选择刀沿
    28085: 指定TO单元到通道
    用来定义为适当通道定义哪个TO存储器
    18100: 每个TOA程序块刀具偏移
    由NCK管理的所有刀具的刀沿的最大数量由该参数设定
    18105 D号的最大值
    所允许定义的最大D号。
    18106 每个刀具号D号的最大数量
    $TC_DPCE[t,d].
    18102: MM_TYPE_OF_CUTTING_EDGE. D编号类型类型
    the ‘18102’ function is active, only one D offset can be defined in the TO unit.
    TOOL_CHANGE_ERROR_MODE Bit 0 = 1).
    If a program error has occurred, the line with the error cannot be corrected (Txx); only the line at which the program stopped and which generated the alarm can be edited
    11346 手轮缺省路径或速度
    = 1 通过该参数设定手轮距离。在DRF手轮移动的过程中，可以仅仅通过指定增量一半的距离来移动轴。
    20360 定义刀具参数
    通过设定位9等于1，来定义移动轴中作为直径偏置的DRF偏置。当取消轴的DRF偏置，则现存的刀具偏置同时取消。
    18102 D编号类型类型
    = 0 默认设置
    _ Value = 1 = flat D number structure with absolute direct D programming
    Cutting edges can be deleted individually via PI command or NC programming command.
    Cutting edges with a specific number can also be created selectively using the MMC.
    18100
    MM_NUM_CUTTING_EDGES_IN_TOA is used to set the maximum number of D or offset data blocks (max. 600).
    The following machine data affect the way tools and cutting edges (D numbers) work in the NCK:
    20270: CUTTING_EDGE_DEFAULT
    20130: CUTTING_EDGE_RESET_VALUE
    20120: TOOL_RESET_VALUE
    20121: TOOL_PRESEL_RESET_VALUE
    22550: TOOL_CHANGE_MODE
    22560: TOOL_CHANGE_M_CODE
    20110: RESET_MODE_MASK
    20112: START_MODE_MASK
    20090 = 2 ;
    Spindle no. 2 is master spindle
    20110, bit 3 can be used to define that the active tool and the tool offset are transferred as follows:
    _ Bit 3=1 from the last test program to finish in test mode, or
    _ Bit 3=0 from the last program to finish before activation of the program test
    Prerequisite Bits 0 and 6 of MD 20110 must be enabled.
    18082 MM_NUM_TOOL ：NCK（SRAM）所能处理的刀的数量。
    18088 MM_NUM_TOOL_CARRIER ：刀柄（toolholders）数量
    18094 MM_NUM_CC_TDA_PARAM Number of TOA data FBW, S7
    18096 MM_NUM_CC_TOA_PARAM Number of TOA data which can be set up pertool and evaluated by the CC
    18100 MM_NUM_CUTTING_EDGES_IN_TOA Tool offsets per TOA module S7
    18102 MM_TYPE_OF_CUTTING_EDGE Activate flat D number management (_ SW 4)
    18105 MM_MAX_CUTTING_EDGE_NO Address extension interpreted as spindle number
    18106 MM_MAX_CUTTING_EDGE_PERTOOL Maximum number of cutting edges per tool
    18108 MM_NUM_SUMCORR Number of all sum offsets in NCK
    18110 MM_MAX_SUMCORR_PER_CUTTEDGE Maximum number of sum offsets per cutting
    edge (SW 5 and higher)
    7.2 Machine data
    18112 MM_KIND_OF_SUMCORR Properties of sum offsets in the NCK
    18114 MM_ENABLE_TOOL_ORIENT Assign orientation to cutting edgesChannel-specific ($MC_ ... )
    20096 T_M_ADDRESS_EXT_IS_SPINO Spindle number as address extension
    20110 RESET_MODE_MASK Definition of control basic setting after power-up and RESET parts program endK2
    20120 TOOL_RESET_VALUE Definition of tool for which tool length compensationis selected during power-up or onreset or parts program end as a function of MD
    20110
    20121 TOOL_PRESEL_RESET_V　

评论仅代表评论人个人看法，不表明博客主人及中国工控网同意其观点或其描述共1条评论共1页第1页

评论人署名：WU998

评论时间：2016/6/4 21:19:00

我要发表评论

看看

共1条评论共1页第1页

发表评论

登陆网站发表评论

密码：